[i=s] 本帖最后由 dengbao2001 于 2011-10-26 15:08 编辑 [/i]
我有一个Compellent存储，给一台RHEL5.5的服务器划算了2个卷，通过编辑Multipath.conf文件，两个卷分别被识别了。但是我需要正常将两个卷从RHEL5.5中卸载，我执行了如下操作
屏蔽了Multipath.conf中的Multipath的两个卷的配置的映射，参考下面完整的Multipath.conf文件
# This is a basic configuration file with some examples, for device mapper
# multipath.
# For a complete list of the default configuration values, see
# /usr/share/doc/device-mapper-multipath-0.4.7/multipath.conf.defaults
# For a list of configuration options with descriptions, see
# /usr/share/doc/device-mapper-multipath-0.4.7/multipath.conf.annotated
# Blacklist all devices by default. Remove this to enable multipathing
# on the default devices.
#blacklist {
# devnode "*"
#}
## By default, devices with vendor = "IBM" and product = "S/390.*" are
## blacklisted. To enable mulitpathing on these devies, uncomment the
## following lines.
#blacklist_exceptions {
# device {
# vendor "IBM"
# product "S/390.*"
# }
#}
## Use user friendly names, instead of using WWIDs as names.
defaults {
user_friendly_names yes
}
##
## Here is an example of how to configure some standard options.
##
#
#defaults {
# udev_dir /dev
# polling_interval 10
# selector "round-robin 0"
# path_grouping_policy multibus
# getuid_callout "/sbin/scsi_id -g -u -s /block/%n"
# prio_callout /bin/true
# path_checker readsector0
# rr_min_io 100
# max_fds 8192
# rr_weight priorities
# failback immediate
# no_path_retry fail
# user_friendly_names yes
#}
##
## The wwid line in the following blacklist section is shown as an example
## of how to blacklist devices by wwid. The 2 devnode lines are the
## compiled in default blacklist. If you want to blacklist entire types
## of devices, such as all scsi devices, you should use a devnode line.
## However, if you want to blacklist specific devices, you should use
## a wwid line. Since there is no guarantee that a specific device will
## not change names on reboot (from /dev/sda to /dev/sdb for example)
## devnode lines are not recommended for blacklisting specific devices.
##
blacklist {
wwid 26353900f02796769
devnode "^(ram|raw|loop|fd|md|dm-|sr|scd|st)[0-9]*"
devnode "^hd[a-z]"
}
#multipaths {
# multipath {
# wwid 36000d3100032dd000000000000000005
# alias test02
# path_grouping_policy multibus
# path_checker readsector0
# path_selector "round-robin 0"
# failback manual
# rr_weight priorities
# no_path_retry 5
# }
#multipath {
# wwid 36000d3100032dd000000000000000003
# alias quorum
# path_grouping_policy multibus
# path_checker readsector0
# path_selector "round-robin 0"
# failback manual
# rr_weight priorities
# no_path_retry 5
# }
# multipath {
# wwid 1DEC_____321816758474
# alias red
# }
}
#devices {
# device {
# vendor "COMPAQ "
# product "HSV110 (C)COMPAQ"
# path_grouping_policy multibus
# getuid_callout "/sbin/scsi_id -g -u -s /block/%n"
# path_checker readsector0
# path_selector "round-robin 0"
# hardware_handler "0"
# failback 15
# rr_weight priorities
# no_path_retry queue
# }
# device {
# vendor "COMPAQ "
# product "MSA1000 "
# path_grouping_policy multibus
# }
#}
保存文件
multipath -F
Service multipathd restart
执行 ls - /dev/mapper 仍然可以看到映射的卷。
另外一个怪问题，两个卷我分别取了别名，参考配置文件，但是在/dev/mapper下面 显示却如(Mpath1,mpath2)
total 0
crw------- 1 root root 10, 63 Oct 26 19:54 control
brw-rw---- 1 root disk 253, 6 Oct 26 20:09 mpath1
brw-rw---- 1 root disk 253, 7 Oct 26 20:09 mpath2
请帮忙看看，谢谢！
beijk222@126.co 于 2014-07-04 17:40:30发表:
很强大的样子
于 2014-06-21 21:30:41发表:
你的编号需要用双引号扩起来，我最近也是在做，同样问题。就是引号的问题
dengbao2001 于 2011-10-29 18:36:26发表:
顶上去，谢谢！
dengbao2001 于 2011-10-27 22:23:52发表:
有朋友会吗？